what are you looking for?
Tubular inspection NDT system with ECT and RFT functions for both ferrous and non-ferrous tubes. Mixing function enables noise signal remove from the support plate, and tube sheet mapping enables to draw the tube layout and to mark the testing result with different colors.
This powerful ECT instrument is designed with 2 channels, 4 frequencies, mixing unit and tube sheet mapping. It’s widely used for inspection of small pipeline, heat exchanger tubes and boiler tubes from tube ID, mainly for non-ferrous materials.
Tube sheet mapping draws the tube layout and marks the testing result with different colors. Mixing unit removes signal from support plate and leaves only defect signal. Inspection settings for different applications can be stored in files and simply called up when needed. And different types of report can be generated for analysis and record.
|
Specifications |
|
|
Battery |
Lithium battery, long working time of 10 hours per charge |
|
Channel |
2 channel |
|
Frequency |
4 frequencies per channel with 64Hz-5MHz |
|
Mixing Unit |
mixing unit to suppress noise signal at a constant frequency |
|
Tube Sheet Mapping |
Tube sheet mapping draws according to real tube layout, and testing result is marked in different colors |
|
Calibration |
Calibration on known flaws and automatic generation of calibration curve. Calibration data can be saved and simply called up when needed |
|
Probe Type |
Differential, absolute, DP, encircling coil, pencil, flat, sector, array etc. |
|
Screen Display |
Real-time strip chart, impedance plane , tube sheet display |
|
Report |
Automatic generation of report in different format |
|
Alarm Output |
One hardware alarm output with triode OC gate |
|
Gain |
0-90 dB in 0.5 dB steps |
|
Phase |
0-359° in 0.1° steps |
|
Gain Ratio (Y/X) |
0.1-10 |
|
Impedance Display Mode |
Point, Line, Auto |
|
Filter |
High pass: 0-500 Hz; Low pass: 10-10000 Hz; Digital: 1-100 |
|
Drive Voltage Level |
1-8 levels |
|
Background Coordinate |
Rectangular coordinate, polar coordinate |
|
Power Supply |
Built-in lithium battery (14.8V, 5.7AH) |
|
Standards |
ASTM, JB/T4730.6-2005, DLT 883-2004 etc. |
|
Balance |
Fast digital/analog electronic balance |
|
Language |
English and Chinese |
|
Operating Temperature |
-20°C to 55°C |
|
Instrument Dimensions |
2.0kg; 290mm x 210mm x 42.5mm |
Real-time strip chart, Impedance plane, Tube sheet display with color mapping
Different reports generated for record and further analysis.
Widely Used For
• Inspect carbon steel and non-ferrous heat exchanger tubes, small pipeline, boiler tubes
• Crack detection for aircraft components, auto parts, axles, machine parts, bolts and so on
• Surface inspection for welds with or without coating
• Sort different heat treatment conditions and different materials
|
MODEL |
CHANNEL |
FREQUENCY |
ECT |
RFT |
VIDEO |
TUBE SHEET |
|
EEC-39RFT++ |
8 |
8 for each channel |
√ |
√ |
√ |
√ |
|
EEC-39RFT+ |
8 |
8 for each channel |
√ |
√ |
× |
√ |
|
EEC-39RFT |
2 |
4 for each channel |
√ |
√ |
× |
√ |
|
EEC-39 |
2 |
4 for each channel |
√ |
× |
× |
√ |
|
EEC-35RFT |
2 |
2 for each channel |
√ |
√ |
× |
√ |
|
EEC-35++ |
2 |
2 for each channel |
√ |
× |
× |
√ |
EEC-309 is designed with MIMO and OFDM technology, which greatly improves the testing speed of RFT. It is widely applied for high speed tube inspection, heat exchangers inspection, condensers inspection etc. It also enables to inspect defects and check wall thickness at the same time.
Learn More
EEC-FT wire inspection ECT is designed with 5 independent testing channels which can test 5 lines at the same time. The start and end of each channel can be controlled individually. The optional powerful report system makes the testing data analysis easily. It is widely used for tungsten wire inspection and molybdenum wire inpsection.
Learn More
EEC-22D Eddy Current Sorting System is specially used for material sorting, hardness sorting, heat treatment sorting, and flaw inspection of metal tubes, bars, wires, auto parts, valves and various metal components. The difference of structure, case depth can be well separated too.
Learn More
EEC-23 eddy current tester can be used for the on-line/off-line tube inspection, bar inspection, wire testing and so on. Work with different probes and accessories, this machine can realize different functions. For example, with saturation device, it can be used for the inspection of ferromagnetic materials; with special probes of welding, it can be used to test welding quality on line or by hand.
Learn More
Heat exchanger tube inspecton system with ECT and RFT functions for both ferrous and non-ferrous tubes. Mixing function enables noise signal remove from the support plate, and tube sheet mapping enables to draw the tube layout and to mark the testing result with different colors.
Learn More
EEC-F ECT sorting system is provided for hardness sorting, material sorting, and heat treatment sorting. It can be used for inspection and sorting of metal tubes, bars, wires, auto parts, valves and various metal components. The difference of structure, surface hardness, case depth can be well separated too.
Learn More
This new powerful eddy current flaw detector makes the manual inspection much easier, faster and more accurate. Defect inspection, weld inspection, conductivity measurement and coating thickness measurement are all included in this instrument. The all-in-one design makes the small body with strong function.
Learn More
With 4-channel and 2-frequency design, this eddy current crack detection instrument enables high-sensitivity and high-efficiency manual inspection. Inspection settings for different applications can be stored in files and simply called up when needed.
Learn MoreWants To Get Latest Updates! Sign Up For Free.
